Just go to http://soldersmoke.com. On that archive page, just click on the blue hyperlinks and your audio player should play that episode.
http://soldersmoke.com
I've been hearing about this rig for many years. It first appeared in the September 1994 issue of QRPp, the journal of the NORCAL QRP club. A condensed version of that article appeared in SPRAT 81 (Winter 94-95). The designer is Derry Spittle VE7QK from Vancouver, British Columbia. The name always puzzled me. Here is the explanation: It started with the Neophyte: A very simple direct conversion receiver that many of us built. The Neophyte was mostly an NE602 and an LM386. In the Epiphyte, a crystal filter and a second NE602 were added, turning the Neophytes into a superhet receiver and -- with some additional circuitry -- an SSB transceiver. The Oxford English Dictionary reportedly defines an Epiphyte as "a plant that grows on another plant"(see picture below). The Epiphyte grew out of the Neophyte.
And this plant grew in British Columbia, which seems -- like Australia and New Zealand -- to be fertile ground for simple phone rigs. I'm pretty sure the "Wee Willy" DSB rig also came out of BC, and it may have had a similar purpose: allowing for portable contact with the BC Public Service Net on 75 Meters.
There are many features of the Epiphyte that I like: There is a simple 455 kHz filter and a ceramic resonator BFO/Carrier oscillator. The original design featured a VXO-like circuit using a ceramic resonator at 4.19 MHz. And it ran off AA batteries (as did the NE602 DSB rig I took to the Dominican Republic).
Unlike my NE602 rig, the Epiphyte made an artful use of the fact that NE602's can be set up to have TWO inputs and TWO outputs. Where I used DPDT relays to switch inputs and outputs from both NE602s, OM Spittle left all the inputs and outputs connected, and simply switched the VFO and BFO signals. Ingenious.
There were updates and improvements. The Epiphyte 2 and 3 featured increased power out (5 watts vs. 1 Watt). Version 3 has an IRF-510 in the final, driven by a CA3020A chip. That chip is capable of 70 db gain. Wow.
In 1996 NORCAL and G-QRP donated 50 EP-2 kits to radio amateurs in third world countries. Very nice.
In 2000 NORCAL did a kit of the EP-3 -- it sold out in 24 hours. Here is a nice article on the EP-3: http://www.norcalqrp.org/files/Epiphyte3Mnl.pdf And above we have a video from Japan of an EP-3 in action.
I built a version 2B from a Far Circuits PCB. It works great. I strung up a long wire on a rail fence with a tuner at the end and worked 4 states on 75M nets. I spoke with a ham in Madison, WI running 1000 watts and he was astonished he was hearing my 5 watts. John KC9OJV
"SolderSmoke -- Global Adventures in Wireless Electronics" is now available as an e-book for Amazon's Kindle.
Here's the site:
http://www.amazon.com/dp/B004V9FIVW
Re: Scrapping a Classic
-
Too bad we are so far apart. Curious as to how large the mod iron and
reactor are.
I'm curious about the meter panels but I sense they are not anything l...
April 24, 2024. Are you Biased?
-
Shame on you! We are not talking about the criminal trial of a former
president nor the situation in the Middle East. The subject is the Bias
setting on yo...
Scott’s “Fun Harbour-Side POTA”
-
Many thanks to Scott (VA3EKR) who shares the following field report: Apr.
15, 2024, Great Lakes Waterfront Trail Recreation Site (CA-6003) by Scott
(VA3EKR...
An Inline RF Step Attenuator for QRPp Work
-
I don’t need to explain the attraction of low power operation; if you’re
reading this, the chances are that you are already a convert. I’ve been
operating ...
Using an external clock with the RX-888 (Mk2)
-
*The RX-888 (Mk2) and external clocking*
*Figure 1:*
The RX-888 with external clock input *(right)*
The enable/disable switch is barely
visible behind the...
A 51S-1 Restoration Story
-
I came across my Collins 51S-1 in a big junkyard in Ankara, Turkey around
2012. It was in a pile with a lot of other electronic scrap, probably from
one o...
New QRP Cluster Online From OM0ET and OM6APN
-
By DX EXPLORER
DX EXPLORER
Paul OM0ET and Peter OM6APN recently launched a new cluster dedicated to
QRP operations. Have a look and I hope you will enjoy...
3D Printing The Hadley 114mm Newtonian Telescope
-
Yes, we’re building a 3D Printed Newtonian Telescope called Hadley. It’s
being printed in PETG and in the video below, I give a quick tour. My build
isn’...
3D printed project boxes
-
I have been busy with some other things that have kept me away from
electronics projects for quite a while. Now I can get back to them, but
realize I n...
Daylight Again – An all Analog Radio
-
What’s all this? In 10 seconds, A high performance, 7MHz, 5 watt SSB rig
Draws just 24 mA of current 90 dB dynamic range, 80 dB close-in dynamic
range 3D ...
Adding Enclosure to your sBitx Boards Order
-
The early buyers of the sBitx board set who bought it for $270 USD might
want to also add the enclosure (box) for in the kit. What you will now get
is a f...
Digi-chirp! Digital synthesis of ‘nostalgic’ CW
-
The bottom ends of 80, 40 and 20m are not what they used to be. For
starters, the busiest part is the digital segment where computers talk to
computers – l...
-
A Simple Speech Processor
(For QRP/SSB Homebrew Transceivers )
Over the last few weeks I had been thinking to build a small AF speech
processor to add to...
A New Look for your uBitx!
-
Adding a "Cool Blue" Display to your uBitx!
The standard "green background" with black lettering frequently reminds me
that I suffer from Chronic seasickn...
How fun. Maybe I should get out my EP-3 kit and build it. :-) 73, Jim, AL7FS
ReplyDeleteI built a version 2B from a Far Circuits PCB. It works great. I strung up a long wire on a rail fence with a tuner at the end and worked 4 states on 75M nets. I spoke with a ham in Madison, WI running 1000 watts and he was astonished he was hearing my 5 watts. John KC9OJV
ReplyDelete